Here room tips and also general accuse on installing ceiling tiles. They can help you conserve time and also effort as soon as you start the job.

Be certain to follow manufacturer"s instructions for installation, specifically if you"re using cement or adhesive. Inside this file you will discover information about:Selecting the best tilesDetermining exactly how to apply tilesHow to identify the dimension of border tilesApplying tile v adhesivesInstalling tiles on lumber furring stripsInstalling the furring stripsStapling tiles come furring stripsTiling about posts or tube


Most ceiling tiles room made of fiberboard, a mixture of well fibers reduced from hardwood or cane and also chemical binders, which space pressed into semihard, level panels. One-of-a-kind chemicals are added during this process to do fire-resistant tiles.

You are watching: How to install 12x12 ceiling tile

Standard tiles measure up 12" by 12", return tiles are likewise made in 12" by 24" and other sizes. Many ceiling tiles have tongue-and-groove edges for less complicated installation. Friend can choose from plain, embossed and patterned finishes. Some are molded with special texturing and also square edge – instead of the typical beveled edges – to make seams proper visible once the tiles are in place. Acoustical tiles space made native the same form of fiber, but an additional manufacturing procedure helps this tiles absorb lot of the sound in a room. A well-designed acoustical tile absorbs as much as 70 percent of the overabundance noise in an area.Ask your retailer to aid you estimate the materials you require for a brick installation. Most manufacturers carry out charts come the retailer to aid estimate the number of tiles, the lot of furring, and also the gallons of adhesive needed, based on the room size.Manufacturers typically pack 12" by 12" ceiling tiles in cartons the 40, and 12" through 24" tiles are packed 20 to a carton.


The two most common methods that ceiling tile application space to use adhesives or to clip or nail the tiles to wood furring strips. A third system entails a metal grid rather of furring strips and metal clips instead of glue or nails.For ceilings do of sound plaster, gypsum board, or other product that provides a sound, smooth, consistent backing, use adhesives to apply the ceiling tiles.If the ceiling has exposed joints, cracked plaster, or any type of other unsound surface, use furring strips and also nail or staple the tiles come the furring strips.


FIG. 1 - cut tiles at opposite ends of the room should be the exact same size, and they should never be less than fifty percent the width of a full tile.


All reduced tiles should be supplied for the edges of the room whereby the ceiling meets the wall surfaces (Fig. 1).Cut tiles at opposite ends of the room need to be the exact same size.Cut tiles must never be less than fifty percent a tile wide.


measure the total distance from wall surface to wall surface on the longer side of the room. If the size measures in precise feet, you will certainly not should cut any border tiles for that direction. If the street does no come the end in precise feet, include 12 come the number of inches remaining and divide by two. This gives you the broad of her border tiles. For example, if the room is 10"6" long, add 12 to the 6, division 18 by 2, and also the result, 9", is the ideal width of her border tile. (Adding 12 guarantees that your border tile will be much more than fifty percent the broad of a complete tile.)Use the same measurement technique for the shorter side that the room.


FIG. 2 - Chalking present on the ceiling follow me each next of the room that equal the width of a border tile from the wall surface will aid align the border rows.
FIG. 3
- ar the adhesive in each edge of the tile about an inch from the edge and in the middle.
FIG. 4
- location the corner tile in place so that is edges line up v the chalk lines and the flange is exposed.
FIG. 5
- ar several border tiles in place along every edge, then fill in the ceiling with complete tiles.
FIG. 6
- download a border molding because that a neat and finished appearance.


Use adhesive for using tiles only if the ceiling is sound and even. If the is not, use the furring strip an approach (see step 6). surface preparation is essential when making use of adhesives. Any kind of painted surface need to be checked carefully–the paint may flake, peel or end up being chalky, and your tiles will certainly not adhere. You can test painted surface by installing 4 or five tiles at various places around the room and waiting 48 hrs to see exactly how well lock adhere. Making use of the technique outlined in step 4 (determining the size of border tiles), make sure that the border tiles will certainly be the very same on opposing sides of the room.Snap a chalk line follow me each next of the room that equals the broad of the border tile from the wall. Use these lines to align the an initial row that border tiles along both the short and long sides of the room (Fig. 2). Reduced your very first border brick to size. This tile fits into the corner, so you have to take into consideration the size of border tiles on both the short and also long sides of the room. For example, if her border tiles ~ above the long side of the room space to it is in 10" and on the brief side that the room only 9", the corner tile should be reduced to measure up 10" by 9". This permits all various other border tiles in the room to line up correctly with her full-sized tiles.Cut border tiles ~ above a flat surface, with the finished side up. Use a an extremely sharp knife or utility knife, and also a clean (preferably metal-edged) straightedge.Place the adhesive or cement in each corner of the tile around an customs from the edge, and also in the center of the brick (Fig. 3).Place the border tile in position in the edge (Fig. 4). Make sure the wide stapling sheet lines up with the chalk marks on both sides. The flange must be exposed therefore the tongue the the following tile have the right to slide into the brick you"ve just placed. This guarantees a hard fit.It might be important to use a staple in every flange to hold the tile in position while the adhesive dries. Monitor the manufacturer"s recommendations.Place number of border tiles in place along each edge, then to fill in the ceiling with full-sized tiles (Fig. 5).Once you"ve installed all the full-sized tiles, you need to measure and fit each border tile carefully on opposing border. Install a border molding to finish the job, and also finish with a neat and finished figure (Fig. 6).


because that a ceiling through exposed joists, unsound plaster or one uneven surface, pond furring strips come the ceiling before applying the tiles. Seasoned, straight-grained soft woods, such together pine, spruce or fir make best furring strips.If the ceiling has joists covert by an currently ceiling, this joists need to be situated and significant before the furring strips are applied. You deserve to locate joists by control a nail right into the ceiling or by making use of a stud finder.Joists are usually situated every 16" or 24". After you locate the an initial joist, measure across 16" and shot again. After girlfriend have identified the spacing, locate and mark all joists through a chalk heat so girlfriend can connect the furring strips without having actually to situate the joists again on each run. Nail the 1" x 3" furring strips across the joists at ideal angles come the joists.Attach the first furring piece on the ceiling immediately versus the wall that operation at best angles to the ceiling joists.


FIG. 7 - reduced a block that wood exactly 12" less the width of one furring piece to use as a positioning guide for the remaining strips.
FIG. 8
- use scraps of furring strips in between complete furring strips to administer a nailing surface for border tiles.


Position the 2nd furring strip so that the distance in between the center of the strip and also the wall surface is the width of your border tile. the is critical that the continuing to be furring strips be exactly parallel come this strip, and also that the distance from center to facility of every furring strip is 12". Among the easiest methods to position the remaining furring strips is to reduced a block of wood precisely 12" much less the broad of one furring strip. Use the block as a guide in placing the continuing to be strips (Fig. 7).Use 8-penny typical nails because that nailing the strips, with one pond at each joist.All furring strips must be level. Use a lengthy level to obtain a reading on all strips together they are added. If needed, insert timber shims between the joists and the furring strips because that leveling. In ~ the walls running parallel come the ceiling joists (at best angles come the furring strips), usage scraps of furring to carry out a nailing or stapling position for the border tiles (Fig. 8).


FIG. 9 - Snap a chalk line along the ceiling on every side that the wall, the broad of a border tile from the wall. ~ above the side whereby the furring strips operation parallel to the wall, the chalk line will run throughout the middle of the strip.
FIG. 10
- Cut and also position your edge tile first.
FIG. 11
- location three staples top top the sheet of the tile versus a furring strip and staple only in the edge on the other edge.
FIG. 12
- location several border tiles in position along every edge, then fill in the ceiling through full-size tiles.


Snap a chalk line follow me both the short and long political parties of the room to align the an initial row that border tiles. These chalk lines will run under the center of the furring strip on one side and throughout the furring strips ~ above the various other side (Fig. 9).Cut your an initial border tile to size. This brick fits into a corner, therefore you must take into factor to consider the size of the border tiles top top both the short and long sides of the room. For example, if your border tiles on the lengthy side of the room are 10" and also on the brief side that the room only 9", the corner tile need to be reduced to measure up 10" by 9". This allows all various other border tiles in the room to line up appropriately with her full-size tiles (Fig. 10).When you cut these first border tiles, cut off the side without the broad stapling edge. The broad stapling flange should be exposed so the tongue the the following tile have the right to fit into the groove the the brick you"ve simply placed. This promises a hard fit.Staple the brick in place, with three staples top top the edge that is fully against a furring strip and staples just in the corner on the various other edge (Fig. 11).Place several border tiles in position along each edge, then to fill in the ceiling through your full-sized tiles (Fig. 12).After working your way across come the the contrary wall, you should measure and fit each border tile closely on opposing border.Install a border molding to finish the job. The molding also holds the final border tiles in location where over there is no flange left because that stapling. In ~ the border, where your access to the stapling area is limited, friend can connect the tiles v small, large headed nails. Position the nails as close to the wall surface as possible so the border molding conceals them.


FIG. 13 - reduced the brick in half and trim it to fit the contour of the pipeline or post.
FIG. 14


Fig. 13 illustrates just how ceiling tiles have the right to be fitted approximately posts or pipes. Cut the brick in half, then cut each fifty percent to the contour of the pipeline or post.

See more: How To Say Merry Christmas In Germany, How To Say 'Merry Christmas' In German

Fig. 14 illustrates just how to fit ceiling tiles approximately ceiling fixture outlets or smaller sized pipes near the wall. As soon as you"re cut a ceiling tile, constantly be certain to cut the tile challenge up, using a sharp energy knife.
Ceiling Tile Handsaw
nails (Several Sizes) Staples
adhesive Gun Chalk Line
stole Tape energy Knife
Ladder Graph Paper
Furring Strips Hammer
Stapler Adhesive
Caulking Gun urgently Rule
Border Molding Hand Cleaner
Straightedge Tracing Paper
Check your state and local password before beginning any project. Follow all security precautions. Info in this paper has been furnished through the national Retail Hardware association (NRHA) and associated contributors. Every effort has been made come ensure accuracy and safety. No NRHA, any type of contributor nor the retailer deserve to be hosted responsible for loss or injuries result from the usage of the info in this document.