ranging from car repairs, residence appliances, electric troubleshoots,solar systems, workshop equipment, to architecture builds. --> NOTICE- need a an answer from me? Please review -Need answers to Issues-(tab directly listed below this note)


If you have recently discovered that your Kenmore Washing device Model 110, 90 Series- conventional or High volume is leaking water within of your bath tub more than most likely your washer"s water inlet solenoid valve is faulty and also needs replacing.As for me, I started hearing a drip at night as soon as all was quiet and also I was preparing to retire because that the evening. I opened the washer"s door and also noticed the plastic water circulation cowl had water dripping indigenous it. I knew the water inlet solenoid valve had to be the culprit.The tools you will need for the job... -standard screwdriver-phillips screwdriver-channel lock pliers-don"t forget the 1/4" nut runner- it just makes the project easier.

You are watching: Kenmore 90 series washer model 110


*

First things- unplug the washing machine"s strength cord.
*
Next girlfriend will should remove the regulate panel"s end covers. This is really simple, you simply master the top portion of the sheathe as seen in the snapshot below. Traction the peak rear portion up and also towards you, simply be easy and you will be fine. You carry out not need any type of tools for this. This covers snap right off and also expose the screws which need to be removed.
*
*
*
There are two screws, one located at each end of the regulate panel. (see note on photo). Remove these 2 screws in order to remove the washer"s exterior cabinet.
*
Once the screws are removed understand the control panel by every end....pull towards you and also then upwards come dislodge the locking dawgs in the cabinet. As your gently pulling the regulate panel in the direction of you it will certainly hit a stop, right now you have the right to just revolve the bottom upwards.
*
Carefully rotate the regulate panel rearward.
*
The peak will remain in the position (pictured below) - just completely invert the control panel and also you will be able to feel the locking system that will hold the panel in the position. As soon as you feel its secure, it have to stay.
*
*
Now grab her stout and sturdy traditional screwdriver. This will enable you to remove the washer"s housing. Insert the screwdriver down right into the tensioner system by placing the tip in the front valley of the tensioner. Push down...and relocate the manage rearward all in one motion. You will feel the tensioner being released.
*
Remove this two stress springs (one on each side) and also simply reinstall them in the turning back manner. (To install: after placing ago into their ideal location, merely use the screwdriver and push castle downwards till they snap earlier in place. The simple)
*
Do not forget to unplug this harness connection here prior to attempting to move the cabinet. It could require a little assistance through the usage of a screwdriver. Just be careful and also take your time so that you don"t break the small plastic connector"s locking tab mechanism.
*
*
Carefully grab both corners that the cabinet and also pull it towards you. Simply be careful at this suggest that the bottom former of the cabinet doesn"t "fall off" tabs i beg your pardon would permit the real estate to strike your nice hardwood flooring perhaps. Simply be cognizant the this and also you"ll it is in fine.
*
Just absent it appropriate towards you. It will certainly pivot. Ensure that isn"t recorded on anything and remove the completely.
*
Now revolve the water valves off...remember the left valve is the warm valve and the right valves are always the cold valves, at the very least in north America anyway. Only three things anyone really requirements to know in stimulate to it is in a plumber - warm is top top the left, cold is top top the right and poop doesn"t operation up hill-. As long as you can retain that, you"ll it is in fine in the pipes department. LolPlease overlook the nastiness inside my valve regulate box, that is no readily accessible during our program dusting days.
*
After having actually turned both water valves off, eliminate the hoses from the water inlet valve housing. You may need to use some channel lock pliers to ease the fitting, just use caution. (If you use the pliers to snug the fittings ago onto the new valve just go easy. SNUG...it doesn"t have to be too many tight...there space rubber washers within the fitting to certain water doesn"t leak. So carry out not overtighten those connections. Just snug will certainly do!) remove this single screw which is stop valve body to the panel. Pretty to have actually a nut runner to stop slipping and also such in tight quarters.
*
Simply ar water inlet hoses within of washer"s bathtub to allow water to run into tub instead of leaking ~ above the floor.
*
Notice the position of the water inlet valve (blue in shade with solenoids attached). The terminal v the white cable is for the cold and also the one through the red wire is because that the hot part of the valve. Just remember the red lead goes back on the bottom.
*
*
Here is the brand-new solenoid controlled water inlet valve.
*
Install water tap on brand-new one and ensure the water tap clamp is securely in place, landing behind the barbed end of the water tap inlet.
*
*
*
Install screw to host valve housing in place.
*
Now is a great time to take a peek roughly inside the the washing machine and inspect out the various other components. I discovered a rusty, practically useless water tap clamp on my washer"s plastic, water distribution cowl which i replaced.
*
*
*
*
Next slide cabinet back into place:The prior of the cabinet have to slide under the frame"s reduced lip, however the political parties of the room sit on optimal of the frame"s sides. The frame"s steel protrusions pointing upwards fit into slots in the cabinet"s bottom. Just ensure they find their proper home and also replace other materials in turning back order. The pic listed below is looking inside of the cabinet towards front.
*
*
The culprit of the consistent water leak dripping water inside of mine washing machine"s tub. This valve however, has actually served it"s time, because that it has remained in my Kenmore 90 Series, version 110 high volume washing an equipment for end 10+ years.
*
Valve replaced, water turned ago on and the washing machine assembled. 25-35 minute job. Absolutely something one have the right to do in one evening.

See more: How Much Does It Cost To Get Your Tongue Split Ting Cost? Tongue Splitting

*
If this picture tutorial was beneficial, you re welcome let me know by donating. It takes a the majority of time, effort and energies to create the blog because that others to benefit from.